4 Easy Ways to Find a Hole in an Air Mattress Quickly!

The air mattress is a very convenient bed. It is flexible to use whenever a visitor shows up to spend the night and whenever you feel like sleeping in your backyard or go camping.


Air mattresses are also space savers especially if you have a small house or you have many guests and only one guest bed. You can just pump it up and store it easily after use by deflating. However, it is also vulnerable.

Even a small leak can leave the user sleeping on the floor throughout the night. So if you have one, you definitely have to learn how to find a leak in an air mattress.

Finding holes in an air mattress is similar to finding a needle in a haystack. But there are several ways manufacturers have devised for owners to solve this dilemma.

Note that before inspecting your air mattress for leaks, you must remove the bedding and sheets first for an easy check-up. With the following methods, you can quickly learn how to find a hole in an air mattress.

1. Check the Valves First

The valves are the most sensitive part of the air mattress. It is usually the first one give up. The seams only come in second.

  • Position the air mattress in a place where you can freely maneuver. Make sure that there’s enough space for you to flip and inflate it. As much as possible, do not find for holes in dim areas.
  • Fill it with air with the air pump that came with it, or you can manually breathe in it to inflate the mattress. Pump it full of air but not too much that would cause it to burst.
  • Get a good look at the valve because it is often the primary source of leaks in air mattresses. The valve plug should be completely inside the valve stem.
  • For those air mattresses with double locking valves, ensure that the valve stem is pressed hard against the stop just behind it.
  • If you notice that the valve plug does not lock against the valve stem, try to insert a thin plastic for an easy fix.
  • If you don’t see any problem with the valve plug, you can look for the leak elsewhere.

2. Try the Dishwashing Trick

Dishwashing liquids are very bubbly. That’s why it is a neat trick in finding holes in air mattresses.

  • Pour a few drops of liquid dishwashing soap in a spray bottle with warm water. Shake it vigorously so that the soap will be evenly distributed to the air mattress.
  • The key to this trick is to make sure that the brand of dishwashing liquid is good in making bubbles.
  • Spray the soapy liquid around the valve. If air is escaping, you can easily see bubbles form in the area where the hole is especially if the mattress is fully inflated.
  • Spray the soapy liquid all over the air mattress. From the seams and the whole surface, ensure that all spaces are covered.
  • You may get soap on the mattress but do not worry, you can easily wipe it dry with a dry cloth or let it dry under the sun or by using a fan.
  • Once you’ve located the leak, wipe the are dry and encircle the hole using a permanent marker.
  • If you've marked all the holes, let the air mattress dry in direct sunlight for two to three hours. If you do not dry the mattress, molds may form, especially in the seams.
  • Once dry, patch the hole with a strong adhesive patch or duct tape.

3. Try Flooding Technique with a Garden Hose

This method uses a lot of water. You’re going to need an outdoor table, preferably a plastic or metal table and put the air mattress on to of it. If your table is made of wood, cover it with newspapers or plastic tablecloth.

  • With an open garden hose, "flood" the outside valve with water. Make sure that the water does not go inside the air mattress. Look carefully for a leak by concentrating on possible bubbles that pop out while the water is running. If bubbles are forming around the valve, there may be a leak.
  • Pour water over the surface of the mattress. Remember to work slowly. Focus your eyesight around the seams because this is where air escapes often. Flip the mattress and do the process again.
  • Once you’ve found a hole, remove the hose, pat the area with a dry cloth and use a permanent marker to mark the it. Make sure the marker does not quickly blot or smear.
  • After you’ve marked all the possible leaks, pat the air mattress dry with a dry cloth and let it sit under the direct heat of the sun for two to three hours.
  • Once dried, you can now patch the air mattress up with a strong adhesive or duct tape based on the markings you’ve made.

4. Submerging Technique

Before you do this method, check the label in the air mattress first. Some manufacturers do not recommend you to submerge it.

Putting an air mattress under water may saturate the fabric and hasten the material’s deterioration. The protective coating may also separate. So be aware.

  • Deflate the air mattress partly so it would be easy to be submerged under water. A fully inflated mattress will definitely not go underwater even if you push it hard.
  • Submerge the valve stem first in bath tub or pool. Try to force the air out of the valve. If no stream of bubbles is escaping under water, then the valve is clear.
  • Apply pressure while submerging the other parts of the air mattress Submerge parts of the fabric under the water. Seams are second to the valve as the common cause of leaks in air mattresses. Try the method on them next.
  • Mark the leak source with a permanent marker, preferably those that do not bleed and are not water soluble.
  • Pat the air mattress dry and let it dry under the sun for two to three hours.
  • Once it’s 100 percent dry, you can patch it up with adhesive tapes.


Did you find this tips and tricks on how to find a leak in an air mattress useful? Kindly share this information with your friends.

Related Resources:

  • Best Air Mattress in 2019 [Top 10 Comparisons]
  • Best Beautyrest Mattress in 2019 [10 Proven products]
  • Best Firm Mattresses in 2019 [Top 10 Reviews]
  • Best King Size Mattress in 2019 [Top 10 Comparison]
  • Best Mattress for Bad Backs in 2019 [Top 10 Reviews]
Click Here to Leave a Comment Below 0 comments